Rimage DLN5200 User's Guide

Rimage DLN5200/DL5200™ User Guide This manual provides the information needed to operate the DLN5200/DL5200 and identify the parts. To set up and

Rimage DLN5200/DL5200 4 110768_D Operator panel The operator panel has a two-line LCD display that informs you of operations or any conditions that

Identify the parts of the Rimage DLN5200/DL5200 Output trays The Rimage DLN5200/DL5200 is configured with five output trays and an output bin. When a

Rimage DLN5200/DL5200 6 110768_D Rear view - Rimage DLN5200 Printer USB CablePrinter Control Cable Printer Power Cord PC Power Cord Serial Cable

Identify the parts of the Rimage DLN5200/DL5200 Rear view - Rimage DL5200  Note: The 9-Pin serial connector is not used. Printer Control Cable Pr

Rimage DLN5200/DL5200 8 110768_D PC power switch The PC power switch supplies power to the embedded PC and autoloader.  Note: The PC power switch

Operate the Rimage DLN5200/DL5200 Operate the Rimage DLN5200/DL5200 Powering on Before you begin: Set up the Everest printer. For more information, r

Rimage DLN5200/DL5200 10 110768_D Powering off Powering off the Rimage DLN5200 1. Close all open applications. 2. To shut down the software, Wind

Operate the Rimage DLN5200/DL5200 Loading discs The supply bin can be loaded with 50 discs. Use thermal printable discs compatible with the Everest

Rimage DLN5200/DL5200 12 110768_D Maintain the DLN5200/DL5200 The procedures in this section will help keep your DLN5200/DL5200 in optimum operating

Maintain the DLN5200/DL5200 3. Check the disc alignment. To see if the disc is centered, observe the gap between the edge of the disc and the rais

Rimage DLN5200/DL5200 14 110768_D 5. If necessary, perform a front to back alignment. a. Turn the front to back alignment screw until there is a 1/

Operate Gemini Utilities Operate Gemini Utilities The Rimage Producer Software Suite includes an application called Gemini Utilities, which is used t

Rimage DLN5200/DL5200 16 110768_D Learn More Rimage DLN5200/DL5200 specifications  Note: For printer specifications, refer to your Everest Printer

Learn More Operator panel error messages These messages may display on the operator panel. CLAMP FAILURE – The Everest printer tried to clamp a disc

Rimage DLN5200/DL5200 18 110768_D EVEREST PRINTER OPENING ERROR – The print drawer may be obstructed. Ensure that the printer is seated properly on

Learn More Technical support and product updates Support for the DLN5200/DL5200 autoloader is available through your authorized reseller. - Importan

Rimage DLN5200/DL5200 20 110768_D Safety Testing Product name: Rimage DLN5200/DL5200 Model: • DLN5200: RAS15E • DL5200: RAS15 Notice for USA

Learn More Rimage DLN5200/DL5200 Limited 1 Year Warranty/Guarantee Rimage warrants, to the original end user only, that all non-consumable parts of t

Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 00

Rimage DLN5200/DL5200 Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapoli

Contents Contents Introduction ... 1 Requirements ...

Rimage DLN5200/DL5200 ii

Introduction Introduction This manual provides the information needed to operate the DLN5200/DL5200 and identify the parts. To set up and install you

Rimage DLN5200/DL5200 2 110768_D Ribbon requirements For ribbon requirements, refer to the Everest Printer User Guide. Label design requirements For

Identify the parts of the Rimage DLN5200/DL5200 Identify the parts of the Rimage DLN5200/DL5200 This section describes the Rimage DLN5200/DL5200 har